ProScan PS20112 Especificaciones descargar pdf (Pagina 39)

Programming.R,emote to Control_CableBox

If your cable box has its own remote to change channels,

you will probably be able to program the TV's remote to

control both the TV and the cable box.

The TV's remote is designed to control several brands of

cable boxes. To program the remote, just press CABLE,then

ID,then the two-digit code number for your brand of cable

box. Refer to the chart below to find the code number for

your cable box. Press the OFF/ONbutton next to confirm

operation. You may need to try each of the code numbers

listed until you find the one that works.

4 PRESSOFF/ONTO TEST

CABLE

-- 3 PRESSTWO

NUMBERBUTTONS

(see list below)

2 PRESS

_rand ogCable-TV Box Code Number(s)

Anvision 07, 08

Cablestar 07, 08

Eagle 08

Eastern International 02

General Instrument 04, 05, 15, 23, 24, 25, 30, 36

Hamlin 12, 13, 34

Hitachi 37, 43

Jerrold 04, 05, 15, 23, 24, 25, 30, 36

MACOM 37, 43

Magnavox 07, 08, 19, 26, 28, 29, 32, 33, 40, 41

NSC 09

Oak 01, 16, 38

Oak Sigma 16

Panasonic 27, 39

Philips .t 07, 08, 19, 26, 28, 29, 32, 33, 40, 41

Pioneer 18, 20

Randtek 07, 08

RCA 27

_al 12, 13

Scientific Atlantic 03, 22

Sylvania 11

Teknika 06

Texscan 10, 11

Tocom 17, 21

Unika 31

Viewstar 07, 08, 19, 26, 28, 29, 32, 33, 40, 41

Zenith 14, 42

Note: Refer to the information sheet packed with your remote control

for the latest list of brand names and code numbers. Because this list is

constantly growing, the information sheet packed with your remote

control may be a later version of this list and contain additional brands

and/or code numbers.

After the TV's remote is pzogrammed, you'll be able to

turn on the cable box by pressing CABLEthen ON/OFF.You

can change channels on the cable box by pressing the

CHANNELbuttons whenever the remote is in the "cable"

mode, To put the remote in the "cable mode", press the

CABLEbutton. Press the iv button to put the remote back

into the TV mode so the re mote buttons will control the

TV again.

ProgrammingRemoteTo ControlCable Box

with remoteonly

Refer to the chart at the left. to find the code number that

corresponds to the brand name of your cable box. Keep

this number in mind. If more than one number is listed,

you may need to try each one separately until you find the

one that works.

1 Press CABLE button on remote.

2 Press IDbutton on remote.

Press two number buttons (first one, then the other) to enter

the code number for your brand of cable box.

Note: You must press the two number buttons within three seconds

of pressing the to button.

4 Point the remote at the cable box and press the OFF/ONbutton

to test the code number.

• If the right number was entered, the cable box should turn

on. Pressing the CHANNELbuttons should then also change

channels on the cable box.

• If the cable box does not _eact to the remote (or if the remote

turns on the cable box but does not change channels), repeat

steps 1 thru 5 with another" code number.

Operating Notes: After the r_mote is programmed, it will turn on

the cable box whenever you press CABLEand then OFF/ON.

To turn off the cable box, pres,; CABLE,then OFF/ON.

To change channels on the cable box, press CABLEthen CHANNEL

up or down.

¢3

o¢'

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 53 54

Comentarios a estos manuales

Sin comentarios

ProScan PS20112 Especificaciones Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Televisores Lcd ProScan PS20112